Cupra-AL

1. المجتمع
2. Archive
3. How do I make a controllable ball, marble madness style?

It's sorted now in this thread: https://feedback.indreams.me/forums/917434-dreams-how-do-i/suggestions/36349435-advanced-rotator-can-t-get-the-ball-to-rollA couple of tweaks to other settings was r...

• عرض التعليق
• Cupra-AL
• 21 ديسمبر، 2018 12:25
• 1 صوت

1. المجتمع
2. Archive
3. How do I make a controllable ball, marble madness style?

OK, so I'm still stuck on this. I'll start from scratch again but I don't know quite what I am doing wrong. Thanks for all the advice though.One thing to clarify, does the X go to the X and the Y g...

• عرض التعليق
• Cupra-AL
• 21 ديسمبر، 2018 08:52
• 1 صوت

1. المجتمع
2. Archive
3. How do I make a controllable ball, marble madness style?

Luci,I have tried for the past two hours to try and get the ball rolling and it's not budging :o)Is it correct that I should connect the X and Y outputs of the splitter to the X axis speed and Z ax...

• عرض التعليق
• Cupra-AL
• 20 ديسمبر، 2018 20:14
• 1 صوت

1. المجتمع
2. Archive
3. How do I make a controllable ball, marble madness style?

OK, figured gravity out, but I was sure I had set the options, although it is very hard to see sometimes the difference from on & off of certain settings in an object.

• عرض التعليق
• Cupra-AL
• 20 ديسمبر، 2018 17:09
• 1 صوت

1. المجتمع
2. Archive
3. How do I make a controllable ball, marble madness style?

I was about to post a question on gravity when a search found this. I had the same idea for a ball game, but I'm still going to do it.Mine was more about gravity controlling the ball, with the LS t...

• عرض التعليق
• Cupra-AL
• 20 ديسمبر، 2018 16:34
• 1 صوت

1. المجتمع
2. Archive
3. How do I put an object in a puppets hand?

Could you model the object in the puppets hand, make it invisible at the start, then when you pick it up from the floor, make the floor one invisible, and the one in the puppet creation visible?

• عرض التعليق
• Cupra-AL
• 20 ديسمبر، 2018 18:38
• 1 صوت

1. المجتمع
2. Archive
3. How do I snap to the grid lines.

I agree, I work with grids and I always have them at top surface of an object. I soon realised that Dreams centres objects, so to get them level they have to be the same thickness, or align by eye ...

• عرض التعليق
• Cupra-AL
• 20 ديسمبر، 2018 21:22
• 1 صوت

1. المجتمع
2. Archive
3. Advanced rotator - Can't get the ball to roll.

Christophe...I love you man.

• عرض التعليق
• Cupra-AL
• 21 ديسمبر، 2018 10:53
• 1 صوت

1. المجتمع
2. Archive
3. Door Hinges

Just reiterating what the previous post stated, the tutorial on the last bridge you have to cross using the pink plank and adding two hinges, one either side will hopefully explain it.From memory, ...

• عرض التعليق
• Cupra-AL
• 21 ديسمبر، 2018 23:51
• 1 صوت

1. المجتمع
2. Archive
3. How do I make a posessed puppet strafe left and right

Can't answer about the strafing, but take a look here, the glossary is full of useful information and examples.https://indreams.me/guide/palette-glossary/assembly/components/sensors-and-input/laser...

• عرض التعليق
• Cupra-AL
• 22 ديسمبر، 2018 06:51
• 1 صوت