allan_Huidobro

1. Community
2. Archive
3. How do I make pipes at non-90 degree angles in the grid?

Yah I couldn't figure it out. I uploaded it on dreams as 135/45 degree pipe. Had to use precise move to get it as close as humanly possible to the center. And no I don't see the picture on the post.

• Kommentar anzeigen
• allan_Huidobro
• 22. Dezember 2018 09:50
• 0 Stimmen

1. Community
2. Archive
3. How do I make pipes at non-90 degree angles in the grid?

Just realized, have you tried enabling surface snap? Believe it's only sculpt mode but could help do what you need

• Kommentar anzeigen
• allan_Huidobro
• 22. Dezember 2018 09:06
• 0 Stimmen

1. Community
2. Archive
3. Is this supposed to happen: Paint stays when part moves

Oh okay. Well I think it is supposed to happen, as sculpt mode painting is simply placing shapes of color one can't see. How I would tackle this problem is to create door frame, exit sculpt/create ...

• Kommentar anzeigen
• allan_Huidobro
• 22. Dezember 2018 08:45
• 0 Stimmen

1. Community
2. Archive
3. Edit the object used by an emitter

What I did was create the object I wanted emitted as a separate creation. Then go into scene where I want to emit the thing, import it and select it for emitter. Any time I want to change the emitt...

• Kommentar anzeigen
• allan_Huidobro
• 22. Dezember 2018 08:35
• 0 Stimmen

1. Community
2. Archive
3. How do I place precisely a substract shape to cut another shape in a precise angle ?

L1 and triangle(Tri2 + Tri1) while in sculpt mode to enter edit shape. From there you can hover your imp over the shape you're using to subtract to edit it's dimensions. Or slap the two move sticks...

• Kommentar anzeigen
• allan_Huidobro
• 22. Dezember 2018 08:30
• 0 Stimmen

1. Community
2. Archive
3. What is the best way to make a toggle

Signal manipulator has easily become one of my favorite logic tools due to how much you can do with it. Signal Manipulator -> Custom Remapper -> Edge Mode -> Toggle output at ON

• Kommentar anzeigen
• allan_Huidobro
• 22. Dezember 2018 08:26
• 0 Stimmen

1. Community
2. Archive
3. Straight line

Paint stroke along a grid? or edit a shape via L1 + triangle in sculpt mode, and hover over the shape and increase the length in your preferred axis.

• Kommentar anzeigen
• allan_Huidobro
• 22. Dezember 2018 08:21
• 0 Stimmen

1. Community
2. Archive
3. Is this supposed to happen: Paint stays when part moves

I'm assuming that by saying separate piece, you mean that they are two different sculpts. So you scope in to sculpture, painted sculpture (sculpt mode paint right?) and then scope out, and move the...

• Kommentar anzeigen
• allan_Huidobro
• 22. Dezember 2018 08:16
• 0 Stimmen

1. Community
2. Archive
3. Struggling to make a sphere that rolls using the L stick relative to the camera.

Are you making a new sculpt each time? Sounds like you're editing the shapes within the sculpt. What you can do is enter sculpt mode, select a sphere. Then with L1 + Square (Tri2 + Tri1), forget wh...

• Kommentar anzeigen
• allan_Huidobro
• 22. Dezember 2018 07:38
• 0 Stimmen

1. Community
2. Archive
3. How do I make pipes at non-90 degree angles in the grid?

Have you tried Triangle2 + Triangle1(L1 + Triangle on DS4) over the area you want to place the cylinder to reset the grid? That's how I would go about it when something is not aligned

• Kommentar anzeigen
• allan_Huidobro
• 22. Dezember 2018 07:23
• 0 Stimmen